| 33 0641 01 Rollix Slewing Ring Bearings | B:14.00 mm; d:17.000 mm; Fillet Radius ra:1.00 mm; Grease Speed Rating Open/Shielded n1:12000 rpm; D:47.0000 mm; Basic Static Radial Load Rating Co:8500 N; Accessories:Snap-Ring; Basic Dynamic Radial Load Rating C:14200 N; Oil Speed Rating Open/Shielded n2:15000 rpm; |
| 121.32.4000.990.41.1502 Standard 5 Slewing Ring Bearings | r1 min.:0.6 mm; Lubricant:Regular relubricatio; C:23.8 mm; r2 min.:1 mm; Design (sliding contact surface combination):Steel/steel, heavy-d; rb max.:1 mm; ra max.:0.6 mm; B:27.762 mm; Basic dynamic load rating C:86.5 kN; dk:45.593 mm; b1:5 mm; b:4.8 mm; d:31.75 mm; Specific dynamic load factor K:100 N/mm²; Sealing solution:Triple-lip seals; Specific static load factor K0:300 N/mm²; α:6 °; |
| 121.50.6700.990.41.1502 Standard 5 Slewing Ring Bearings | H1:47.625 mm; A:53.975 mm; B:59.531 mm; H2:28.575 mm; J max.:149.225 mm; Mass bearing unit:3.63 kg; J min.:142.875 mm; Limiting speed:6000 r/min; Basic dynamic load rating C:96.5 kN; s:29.766 mm; Attachment bolt diameter G:12.7 mm; S:0.794 mm; da:36.513 mm; L:187.325 mm; H:98.425 mm; |
| 24 0741 01 Rollix Slewing Ring Bearings | Basic static load rating C0:600 kN; d:90 mm; b:10.2 mm; K:6; Maximum static radial loads F0r max.:630 kN; Maximum dynamic radial loads Fr max.:440 kN; Basic dynamic load rating C:468 kN; Fatigue load limit Pu:72 kN; D1 ≈:147 mm; H max.:65 mm; C:119 mm; Mass bearing:26.7 kg; B:122 mm; D:220 mm; r min.:2 mm; d1 ≈:140 mm; |
| 35 0641 01 Rollix Slewing Ring Bearings | Bearing limiting speed:3400 r/min; Labyrinth ring (dc shaft position):LOR 106; Housing:SAF 220; dc:96.838 mm; H1:114.3 mm; P90°:81.4 kN; Stabilizing ring:2 x SR-1520; Da:180 mm; H:217.488 mm; db:114.3 mm; Mass pillow block:26.8 kg; ba:38.894 mm; Initial grease fill:365.71 g; Cap bolt:2 x 3/4-10 UNC; End plug (suffix Y):EPR 15; Pa:36 kN; P180°:55.6 kN; Cap bolt, SAE grade:5; Ca:55.804 mm; P60°:136 kN; |
| 34 0411 01 Rollix Slewing Ring Bearings | Mass pillow block:137 kg; Da:319.999 mm; N1:28.575 mm; da:165.1 mm; Cap bolt recommended tightening torque:203.4 N·m; A2:317.5 mm; Appropriate attachment bolt size G:1 in; Cap bolt:4 x 3/4-10 UNC; P120°:84.5 kN; Cap bolt, SAE grade:5; ba:75.406 mm; P150°:75.6 kN; R2:41.275 mm; R1:114.3 mm; End plug (suffix Y):EPR 19; J max.:600.075 mm; P180°:89 kN; Initial grease fill:1304.1 g; S:4.763 mm; |
| 34 0641 01 Rollix Slewing Ring Bearings | T:53 mm; Cb min.:5.5 mm; Calculation factor e:0.46; l:7 mm; r5 min.:0.6 mm; b:4 mm; C:42 mm; a:51.239 mm; d:65 mm; Fatigue load limit Pu:28 kN; Basic dynamic load rating C:176 kN; rc max.:0.6 mm; Basic static load rating C0:255 kN; d1 ≈:83.3 mm; Mass bearing pair:1.37 kg; Db min.:97 mm; Limiting speed:6000 r/min; K:3 mm; ra max.:1.5 mm; Reference speed:4000 r/min; |
| 37 0641 01 Rollix Slewing Ring Bearings | d:75 mm; d1:135 mm; Mass shaft washer:0.97 kg; r1,2 min.:1.5 mm; B:12.5 mm; |
| 27 0541 01 Rollix Slewing Ring Bearings | Labyrinth ring (db shaft position):LOR 79; P150°:34.7 kN; Appropriate attachment bolt size G:0.625 in; Da:160 mm; P120°:38.3 kN; R2:27.94 mm; Housing:FSAF 315; H1:101.6 mm; J min.:263.525 mm; Cap bolt:2 x 5/8-11 UNC; P180°:42.3 kN; Ca:64.795 mm; Cap bolt recommended tightening torque:298.3 N·m; da:75 mm; H2:41.275 mm; Pa:27.1 kN; Cap bolt, SAE grade:8; J1:53.975 mm; Labyrinth ring (dc shaft position):LOR 46; |
| 3 0342 05 Rollix Slewing Ring Bearings | B:118 mm; b:13.9 mm; Basic static load rating C0:2160 kN; Basic dynamic load rating C:1449 kN; Reference speed:1100 r/min; D1 ≈:253 mm; d2 ≈:203 mm; ra max.:2.5 mm; Calculation factor Y0:1.8; da min.:194 mm; Calculation factor Y1:1.8; Mass bearing:33 kg; Calculation factor e:0.37; r1,2 min.:3 mm; Limiting speed:2400 r/min; K:7.5 mm; Fatigue load limit Pu:196 kN; d:180 mm; Calculation factor Y2:2.7; |
| 192.40.3550.990.41.1502 Standard 5 Slewing Ring Bearings | N1:19.05 mm; H1:82.55 mm; dc:71.438 mm; Pa:19.6 kN; Max. speed for Taconite seal:900 r/min; Housing:SAF 215; Mass pillow block:12.2 kg; A1:79.375 mm; h:31.75 mm; R2:21.431 mm; P120°:28 kN; RG:1/4 NPT; P90°:45.4 kN; A2:196.85 mm; J max.:244.475 mm; Da:130 mm; Cap bolt:2 x 1/2-13 UNC; PG:1/8 NPT; Taconite seal (db shaft position):TER 79; L:285.75 mm; |
| 33 0741 01 Rollix Slewing Ring Bearings | L:244.475 mm; RG:1/8 NPT; H2:25.4 mm; PG:1/8 NPT; Cap bolt:2 x 1/2-13 UNC; H:134.938 mm; Ca:45.796 mm; Initial grease fill:82.215 g; ba:25.4 mm; Cap bolt, SAE grade:8; P60°:35.1 kN; N1:19.05 mm; R2:17.462 mm; Cap bolt recommended tightening torque:149.1 N·m; Stabilizing ring:2 x SR-1609; A2:171.45 mm; J max.:200.025 mm; Appropriate attachment bolt size G:0.625 in; A1:69.85 mm; P90°:20.9 kN; |